« Overview previous Product 1 / 3 next

HELIX DSP PRO MK2

Digital High-Res 10-channel signal processor with 96 kHz / 32 Bit signal path

HELIX DSP PRO MK2

High Resolution audio at its best!

Thanks to numerous improvements the new HELIX DSP PRO MK2 raises the bar to a new level, not only in terms of sound quality.

Besides the extremely powerful 64 Bit Audio DSP, cutting-edge DA and AD converters with an incredible native resolution of 32 Bit ensure unparalleled sound characteristics. The improved internal power supply as well as the increased maximum output voltage of 8 Volts contribute to the enhanced sound quality of this stunning processor.
Further innovations like the ADEP circuit (Advanced Diagnostics Error Protection) in the highlevel input for circumventing factory-made loudspeaker diagnostic systems, the “Auto Remote” switch for activating / deactivating the automatic turn-on feature of the highlevel input and the software-controlled switch between the optical and coaxial input have been added. 

Of course, the HELIX DSP PRO MK2 provides a HELIX Extension Card slot (HEC slot). This allows adding further interfaces like a Bluetooth® Audio Streaming module or a High Resolution Audio USB soundcard. In terms of design, the DSP PRO MK2 shows up with the HELIX-like clean look and offers perfect preconditions for a fast and simple integration. 

But not only the hardware has been improved – the software as well has been completely revised. Features like the allpass filter option, the increased adjustment range of the time alignment and the switchable sound options of the DA converters are solely a few examples. Despite its extended feature set the configuration of the DSP couldn't be easier thanks to the new DSP PC-Tool V4, which leaves nothing to be desired due to its numerous sound optimization options.  

No doubt - the HELIX DSP PRO MK2 will again make dreams of the most ambitious sound enthusiasts come true - that´s a safe bet!

  • Extremely powerful “fixed point” Audio DSP with 64 Bit resolution and 1.2 billion MAC operations per second
  • AD and DA signal converters of the latest generation with a native resolution of 32 Bit
  • High Resolution audio bandwidth up to more than 40 kHz for unrivalled sound quality
  • HELIX Extension Card slot (HEC) for additional input / output modules like Bluetooth® Audio Streaming, High Resolution Audio Streaming via USB etc.
  • Smart highlevel input with ADEP circuit (Advanced Diagnostics Error Protection)
  • Start-Stop capability down to 6V supply voltage
  • Freely definable signal routing with separate matrices for line, SPDIF and HEC/AUX
  • “Ground lift” switch to avoid ground loops
  • Control input for connecting remote controls and accessories
  • Time alignment with up to 20 ms delay time per channel, additionally reverse time alignment for in-phase summation of the inputs
  • Inputs: 8 x RCA/Cinch, 8 x Highlevel, 1 x optical SPDIF and 1 x coaxial SPDIF
  • Outputs: 10 x RCA/Cinch with max. 8 Volts output voltage

 

Note: The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Audiotec Fischer GmbH is under license. Other trademarks and trade names are those of their respective owners.

96 kHz sampling rate
The HELIX DSP PRO MK2 allows to handle all signals with the doubled sampling rate of 96 kHz. Thus the audio bandwidth is no longer limited to usual values like 22 kHz but allows an extended frequency response to more than 40 kHz. Doubling the sampling rate requires significantly higher DSP power as the number of possible arithmetic operations is halved. Only the implementation of the latest DSP chip generation allows raising the sampling rate to 96 kHz and adding new features plus additional channels at the same time.


Signal converters with a native resolution of 32 Bit
The HELIX DSP PRO MK2 uses high-class AD and DA converters of the latest generation with a native resolution of 32 Bit instead of the common 24 Bit. The result is an unprecedented precision in signal conversion that especially optimizes the sound quality at lower signal levels.


Smart highlevel input
The latest generation of OE car radios incorporates sophisticated possibilities of diagnosing the connected speakers. If a common signal processor will be hooked up failure messages and loss of specific features (e.g. fader function) quite often appears - but not with the DSP PRO MK2. The new ADEP circuit (Advanced Diagnostics Error Protection) avoids all these problems without loading the speaker outputs of the OE radio during high volumes unnecessarily.


Start-Stop capability
The switched power supply of the HELIX DSP PRO MK2 assures a constant internal supply voltage even if the battery’s voltage drops to 6 Volts during engine crank.


Power Save Mode
The Power Save Mode is incorporated in the basic setup. It allows to significantly reduce the power consumption of the amplifiers that are connected to the HELIX DSP PRO MK2 once there’s no input signal present for more than 60 seconds. Please note that in many up-to-date cars with “CAN” or any other internal bus structures it may happen that the radio remains “invisibly” turned on for up to 45 min. even after locking and leaving the car! Once the “Power Save Mode“ is active the remote output and therefore the connected amplifiers will be turned off. The HELIX DSP PRO MK2 will reactivate the remote output within a second if a music signal is applied. It is possible to either modify the turn-off time of 60 sec. or completely deactivate the “Power Save Mode” via the DSP PC-Tool software.


Automatic Digital Signal Detection
Switching from analog input to one of the digital inputs is done automatically as soon as a signal is detected
on the Optical Input or Coax Input. This feature can be deactivated in the DSP PC-Tool software. Alternatively you can use an optional remote control for manual switching between analog and digital inputs.

Inputs 8 x RCA / Cinch
8 x Highlevel speaker input
1 x Optical SPDIF (12 – 96 kHz)
1 x Coax SPDIF (12 - 192 kHz)
1 x Remote In
Input sensitivity RCA / Cinch 2 - 4 Volts
Highlevel 5 - 10 Volts or 10 - 20 Volts
Outputs 10 x RCA / Cinch
1 x Remote Out (max.500 mA)
Output voltage 8 Volts
Frequency response 10 - 44,000 Hz
DSP resolution 64 Bit
DSP power 295 MHz
1.2 billion MAC operations per second
Sampling rate 96 kHz
Signal converters A/D: Asahi Kasei 32 Bit
D/A: Asahi Kasei 32 Bit
Signal-to-noise ratio
(A-weighted)
116 dB (digital input)
110 dB (analog input)
Distortion (THD+N) < 0.0005 % (digital input)
< 0.001 % (analog input)
Crosstalk > 90 dB
Operating voltage 9.6 - 18 Volts (5 sec. down to 6 Volts)
Additional features HEC slot, Ground lift switch, Control Input, ADEP circuit, Auto Remote switch
Dimensions (H x W x D) 40 x 177 x 150 mm / 1.58 x 6.97 x 5.91”

 

1 x HELIX DSP PRO MK2

1 x USB cable

1 x Mounting material

1 x Instruction manual

URC.3URC.3

URC.3

Universal remote control for BRAX, HELIX and MATCH DSP products

DIRECTORDIRECTOR

DIRECTOR

Remote Control with Touchscreen

EPC 5.2EPC 5.2

EPC 5.2

"Easy Plug Cable 5.2" - 5.00 m cable harness for an easy connection of HELIX and MATCH products to factory car radios.

HEC AUX INHEC AUX IN

HEC AUX IN

AUX input module for HELIX devices

HEC BTHEC BT

HEC BT

Bluetooth® input module with Qualcomm® aptX™ codec support for HELIX devices

HEC OPTICAL INHEC OPTICAL IN

HEC OPTICAL IN

Optical input module for HELIX devices

HEC HD-AUDIO USB-INTERFACEHEC HD-AUDIO USB-INTERFACE

HEC HD-AUDIO USB-INTERFACE

High Resolution Audio USB input module for HELIX devices

loading... HELIX DSP PRO MK2 HELIX DSP PRO MK2 HELIX DSP PRO MK2 HELIX DSP PRO MK2 HELIX DSP PRO MK2 HELIX DSP PRO MK2 HELIX DSP PRO MK2 HELIX DSP PRO MK2 HELIX DSP PRO MK2 HELIX DSP PRO MK2 HELIX DSP PRO MK2 HELIX DSP PRO MK2